+- www.chinaphonearena.com (https://www.chinaphonearena.com/forum)
+-- Forum: Brand Specific (https://www.chinaphonearena.com/forum/Forum-Brand-Specific)
+--- Forum: iNew® (https://www.chinaphonearena.com/forum/Forum-iNew%C2%AE)
+--- Thread: [How-To] INEW I6000 blocked (/Thread-How-To-INEW-I6000-blocked)
Pages:
1
2
RE: INEW I6000 blocked - costcant - 2014-03-26
Thanks ROOKAL and thanks STEVENMA61.
In fact, with the help of both, my i6000 1/16 has once again rekindled , and restored to factory condition .
It all works , or works better everything 'that I was able to test, how the camera.
I have not tested the GPS lock on the satellites , but I hope I never have problems.
The only thing wrong is that there are no IMEI codes for which 'll ask ' help later.
But now ' I think it right show as I managed to recover my terminal :
Following the suggestion of STEVENMA61 telling me to try SP Flash Tool, I typed the name on GOOGLE to search for the latest version of the program.
Among the results I found the website forum: XDADEVELOPERS ( General discussion > Upgrading , Modifying and Unlocking > [ Tool] SP flashtool | | Android MTK FLASHER ) and inside the link:
Mediatek - Flash Tool - Downlaod page from which I downloaded the latest version of the program.
After that I installed SP Flash Tool on the computer running it .
I set the file scatter from signing suggeritomi earlier by ROOKAL .
I did recognize my phone from my computer.
I removed the battery.
I started the download with no battery in the phone ( only option accepted from my smartphone) waiting for the message of success of the operation .
I disconnected the phone.
I reinserted the battery.
I tried to turn it on and with a pleasant surprise gave the first signs of life, showing the signal battery charging and an hourglass.
At this point, I do not know if it was necessary , I upgraded the firmware via SP Multiport Download Flash tool exactly as instructed in the post ROOKAL .
Also in this case the attempt of the terminal rievvio showed the same picture of the battery with hourglass.
As it was late, I put the phone on charge and went to sleep.
The next morning I tried re- starting of the engine getting the same picture of the battery with hourglass.
After a few minutes, trying again to accenedere the phone went into recovery mode and from there into operation standard finding the phone as if it had just come out of the factory.
Of course, the whole procedure worked on my phone but I can not absolutely guarantee that it is valid to solve the problems of other phones also because I did not follow a strictly scientific method , a step both for my inexperience , and the fact that in each case the phone was unusable I just tried .
Thanks again for the help given .
At this point there is someone who can ' help to restore the IMEI codes gone ?
RE: INEW I6000 blocked - rookal - 2014-03-26
(2014-03-19, 00:56)costcant Wrote:
I have 3 different ways that you can load the latest stock ROM back on your phone, TWRP, CMW and stock reload.
The best method would be to reload the stock method using SPMultiPortFlashDownloadProject software.
On page 7 of that link, I describe how to do that.
Good Luck.
Rookal Hello, I would like to ask whether the process of installing the new firmware is the same for both models (1/16 GB and 2/32 GB) or vice versa if you need to have the right program for each model, and the same goes for the stock ROM? Personally I bought a INEW i6000 1/16GB.
Sincerely.
The inew 1/16 and 2/32 both use the same ROM. The ROM is just under a gig when unpacked and loaded on your phone.
It's good to hear that you have it working again with the original ROM.
As for the IEME, there is a software that will allow your to modify it but I will have to get back to you on which it is , it's been a while since I have seen it floating around.
But there is also a way to change it from within the phone itself by using dial codes.
I will reply again once I have all the info gathered.
Take Care.
RE: INEW I6000 blocked - costcant - 2014-03-28
Thanks again ROOKAL , in fact , even if indirectly, with your last post did you let me find how to restore IMEI codes of android devices , based on MTK processor .
As you said rightly , too , there are two ways to proceed , both require the rooted terminal :
the first method , a little longer involves the use of a program , the second (the one I used ) on the telephone keypad typing a code that allows you to enter a hidden menu .
In summary I have done so :
- I scored the IMEI codes found inside the phone on a sheet
- I have gained root permissions with the program EROOT
- I opened the phone and I typed on the keyboard * # * # 3646633 # * # *
- I opened the hidden menu
- I tried the command CDS INFORMATION ( I found it on the second page ) and I pressed
- Then I pressed the command RADIO INFORMATION
- I first pressed PHONE 2 obtaining the string AT +
- I deleted it and typed + again + by displaying the string AT + EGMR = 1.10 , " "
- I typed the IMEI code inside the " "
I confirmed by pressing the key COMMAND SENT
- I went back and pressed on PHONE 1 by repeating exactly the same procedure to obtain the string AT + EGMR = 1.17 , " "
- I entered the IMEI number 1 within "" and confirmed again with COMMAND SENT
- I came back out from the hidden menu
- I turned off and restarted the phone
At this point the IMEI coici were in place and I've smartphone running again as before.
At this point I think the thread to be closed
Thanks again to everyone , definitely continue 'to read because they do not even think I can stop fiddling with your phone software